How To Repair Textured Ceiling Video

Textured Ceiling Repair Tips

Updated: May ten, 2022

Make an old ceiling look new over again

Family Handyman

A textured ceiling that's deteriorated or suffered water damage can exist restored to new condition by scraping, priming, and then spraying new texture. It's simpler than it looks.

Y'all might as well like: TBD

Time

Multiple Days

Complication

Beginner

Toll

$101–250

Scrape and prep the ceiling, then texture

Hopper gun

Buy a hopper gun like this and connect it to any 2.v-cfm or larger air compressor.

Photo one: Mask the ceiling

Speed upward and simplify your masking job past applying the tape forth the ceiling showtime. Leave the lower edge of the record loose. And so coil out a length of lightweight poly along the floor, pull one edge up to the ceiling, and stick it to the tape.

Photo 2: Scrape the ceiling

Arrange upward with goggles, a grit mask and a hat before y'all get-go the messy chore of scraping texture. Popcorn spray texture comes off easily if information technology hasn't been painted.

Photo 3: Prime

Paint the ceiling with a fast-drying primer/sealer. Let it dry out before applying the spray texture.

Photo four: Mix the texture

Mix the powdered spray texture and water thoroughly. Lumps will clog the spray tip and could mess up your spray job. Let it residual 15 minutes and remix, adding water if necessary.

Correct texture

Mix slowly, adding water equally needed. The mix should exist like thick paint.

Photo 5: Do beginning

Exercise on paper-thin or a piece of drywall to get a feel for spraying. Adjust the gun'due south tip and trigger until you get a consistent spray pattern that'south easy to control.

Photo 6: Outset at the edges

Starting time by spraying the perimeter, and then fill in the centre. Avert heavy buildup—you tin can always add more.

If your spray-textured ceiling is just muddied or stained, you can renew it with a glaze each of sealer and pigment. But if the texture is falling off or missing in spots, y'all'll have to reapply texture to fix the problem. For small areas, say less than a foot in bore, you could endeavor using an aerosol can of repair texture. But the patch is bound to stick out like a sore pollex. For the best results, you're better off respraying the unabridged ceiling. It's a messy job, simply it'southward not hard to do. In fact, subsequently yous spray one room, you'll probably want to continue going. You tin spray-texture unsightly plaster or smoothen drywall ceilings too. As with most jobs, the primal is in the prep work, which is the fourth dimension-consuming part too. Once the room is masked off, the ceiling prepped and the texture mixed, it'll simply take you about fifteen minutes to spray the ceiling.

If any of the paper drywall record is loose or the drywall is soft or damaged, you'll have to repair and sand these areas first. In improver to the putty knives and drywall joint compound for the repairs, you'll need a wide putty or taping knife for scraping, a roll of 1-1/ii-in. or wider masking tape, plenty painter's plastic to comprehend the walls, a gallon or 2 of primer/sealer, a pocketbook of spray texture (enough to cover 300 to 400 sq. ft.), and a compressor and hopper gun. Yous can buy coarse, medium or fine texture. If y'all're matching existing ceilings, take a sample of the textile with y'all when you purchase the texture and enquire for help matching it. Medium is commonly the all-time choice and will match most ceilings. You can rent a compressor and hopper gun for a half day or buy a hopper gun and connect it to any boilerplate-size or larger compressor. If you utilise a small compressor, you may occasionally have to stop spraying to permit the pressure build upward. Minimize rental costs by getting all the prep piece of work done before you pick upwards the compressor and hopper gun.

Start by removing everything you lot tin can from the room. If you must leave big furniture in the room, stack information technology in the center and cover it with plastic. Cover the floor with sheets or a canvas drop material. Then cover the walls with sparse (1-mil or less) poly sheeting (Photo 1). Painter'southward plastic is very thin and works bully. Go out an opening with overlapping poly at the doorway then you tin get in and out. Plough off the power to the lights and remove any ceiling fixtures. Don't forget to cap the bare wires with wire connectors. Stuff newspaper into the electrical box to keep out the spray texture.

The adjacent stride is to scrape off the old texture (Photograph 2), but not before you've had it tested for asbestos. If it hasn't been painted, it'll usually come off easily. So try merely scraping information technology first. If that doesn't work (you'll know correct away), try wetting the texture with a pump-up garden sprayer. That might make it easier to scrape, but it'll leave a sticky mess on the flooring. If you lot utilise this method, encompass your drib cloths with 4-mil plastic so yous tin can wad information technology upwardly and dispose of the moisture texture and not track it all over the house. Texture that's been painted over can be a lot harder to remove. Just exercise the best you can. Endeavor to knock off the high spots and flatten it equally much as possible. The ceiling doesn't accept to be smooth, but information technology'south easier to become a nice-looking job if nigh of the erstwhile texture has been removed.

When you're done scraping, paint the ceiling with stain-sealing primer (Photograph iii). BIN and KILZ are two popular brands. Use an aerosol can of solvent-based sealer such as BIN white shellac to spot-prime astringent stains. And so pigment the entire ceiling with a h2o-based primer/sealer.

The primal to a successful spray-texture job is mixing the texture to the right consistency. Don't mix it likewise thick. Utilise the corporeality of water recommended on the bag as a starting indicate. So adjust the thickness by adding more water or pulverisation. Mix slowly using a mixing paddle mounted in a 1/ii-in. drill (Photo 4). Mix thoroughly, adding water until the textile reaches the consistency of runny yogurt—or thick paint—with tiny lumps in it. Allow the texture sit for xv minutes, then remix, calculation more water if necessary.

There are a few different versions of hopper guns, just they all take a mechanism at the olfactory organ that controls the bore of the pattern, and a trigger control that helps govern the volume of spray. Start past setting both controls to the center position. Then load the hopper nigh half full with texture material and practice on a piece of cardboard or drywall scrap (Photo 5). Adjust the spray blueprint and trigger until you can get a nice, even pattern without runs or excess buildup. When you're comfortable with the spraying technique, start on the ceiling.

Start past spraying the perimeter (Photo 6). Hold the gun most 18 to 24 in. from the ceiling and aim so that about two-thirds of the spray hits the ceiling and the residual hits the wall. Movement chop-chop around the room, paying special attention to the inside corners where walls meet. Remember, y'all can brand some other pass if it'south too calorie-free. The goal is to comprehend the ceiling with an even layer of texture. Don't worry if information technology looks too polish. The texture volition become more pronounced equally it dries. Be careful to avoid puddles. If you mess up and get a puddle or only a thick buildup, stop and scrape off all the texture with a broad putty pocketknife. Then endeavor again. Movement the gun back and forth while backing up across the room. After you've covered the ceiling, turn ninety degrees and employ some other light glaze at a right angle to the first. Concentrate on filling in lite spots to create an even texture.

When you're satisfied with the consistency of the texture, you lot can clean upwardly the gun, hopper and hose with h2o and pull downwards the poly. If your masking task was a little off and in that location's texture on the wall or flooring, look for it to dry. Then carefully scrape it off and remove the white residue with a wet sponge.

Circumspection!

If yous have ceiling texture applied before 1980, it may comprise asbestos. Before you remove any ceiling texture, contact your state'southward section of environmental protection, department of health or a regional asbestos coordinator for information on asbestos testing and removal. For a list of contacts, go to www.epa.gov/asbestos/pubs/ regioncontact2.html#reg5 For general data on asbestos, get to epa.gov/aspestos.

Required Tools for this Project

Have the necessary tools for this DIY project lined up earlier yous showtime—you'll salvage time and frustration.

You lot'll also need a hopper gun, a mixing paddle and drib cloths.

Required Materials for this Project

Avoid final-minute shopping trips past having all your materials ready alee of fourth dimension. Hither's a list.

Originally Published: June 20, 2022

Like Projects

Source: https://www.familyhandyman.com/project/textured-ceiling-repair-tips/

Posted by: jonesmanout.blogspot.com

Share this post